HACH - Analytical instruments and reagents used to test the quality of water and other liquid solutions.

Alat Uji Kualitas AirPartech OxyTechw² GAL Dissolved Oxygen SensorKategori : Alat Uji Kualitas AirOxyTechw2 GAL Sensor telah didesain untuk menyediakan pengukuran Dissolved Oxygen terpercaya, sensor tersebut menggunakan prinsip galvanik tradisional. HDPE Membrane 100 micron yang keras telah dipilih untuk menyediakan ketahanan/resistensi eksepsional untuk kerusakan. Hal ini dikombinasikan dengan Oxyguard, elektrolit yang unik dan anoda material agar menyediakan ketahanan jangka panjang hingga 3 tahun dan lebih lama tanpa memerlukan pembaharuan sensor atau penggantian membran.Untuk instalasi pada plant limbah aktif (activated sludge plant), Kami merekomendasikan kalau sensor yang dipasangkan menggunakan self-cleaning mounting system, dengan flexible joint pada mounting shaft. Flexible joint menggerakkan sensor dalam proses, menjaga membran bersih dengan menurunkan bio-fouling tanpa menggunakan kompressor dan dengan tambahan keuntungan membuat kotoran jatuh dari kumpulannya. Pergerakan ini sama dengan yang diterima dengan menggunakan kumpulan floating balls, dengan tambahan keuntungan penempatan sensor di bawah permukaan cairan. Ini berarti jika sensor di bawah tingkat lemak apung (floating fats) dan grease yang berakumulasi pada permukaan dan hasil dari pembacaan Dissolved Oxygen akan menjadi lebih representatif di seluruh tangki.OxyTechw2 GAL menyediakan pengukuran terpercaya dan akurat yang dibutuhkan untuk mengoperasikan plant limbah aktif pada konsentrasi Dissolved Oxygen optimal, menjaga keseimbangan antara biaya berjalan blower dan aerator serta kebutuhan produksi aliran yang berkualitas tinggi.Aplikasi.Pengontrolan limbah aktif (Activated Sludge Control),Pemrosesan air minum (Drinking Water Processing),Pengecekan kualitas waduk/kolam/tampungan air (Reservoir Water Quality), &Pengecekan Sungai (River Monitoring).Prinsip Pengukuran.Sel Galvanik (Galvanic Cell)Fitur.Tidak mengendap,Mengurangi pemeliharaan (maintenance),Pembaruan sensor tiap 3 tahun sekali, &Respon cepat.Keuntungan.Kontrol aerasi otomatis, &Kepemilikan yang rendah biaya.Monitor Kompatibel.7300w2 MonitorOpsi Bantalan.Sambungan (joint) fleksibel untuk pembersihan sendiriSensor Alternatif.OxyTechw2 OPTSpesifikasi DataFisikDimensi (TxLxP)Ø58mm, 88 mm panjangBerat0.5 kgProtection ClassIP68Enclosure MaterialPolyoxymethylene (POM) with HDPE membraneCable EntryIntegral Cable GlandPanjang Kabel10 meter standard, 100 meter maksimumInterface ke Monitor Power Supply12 VDC from MonitorSensor OutputModTechw², RS485Data Lingkungan Suhu Penyimpanan/Operasi0 hingga 50ºCLokasiIndoor/OutdoorTingkat Tekanan5 BarPemeliharaan ServisTidak perlu servis rutin Pembersihan berkala dibutuhkan pada frekuensi yang ditetapkan oleh aplikasi. Self Cleaning Shaft Option sangat direkomendasikan, hal ini menghilangkan pembersihan manual antar kalibrasi.KalibrasiSensor dari pabrikan sudah stabil, kalibrasi harus dilakukan untuk menyesuaikan aplikasi. Rekomendasi Pabrikan setiap 6 bulan sekali.

Spesifikasi Hach DR300 Pocket ColorimeterHach DR300 Pocket Colorimeter, the next generation in portable instrumentation. Reduce data collection hassles, eliminate transcription errors, and ensure stronger compliance traceability.• Single Parameter go-anywhere portable photometer• Battery operation for a maximum of 5000 tests• Waterproof instrument IP67 (even better than PCII)• Larger, better display• Data connectivity. Bluetooth to Claros*Alat Laboratorium Umum

Alat Laboratorium UmumLico 690 Professional Spectral ColorimeterCompetence in ColorHigh-performance Spectral Colorimeter for professional color measurements of clear, transparent liquids with reference beam technology. More than 25 color scales included.Exact color calculations which conform to several DIN-ISO-ASTM standards or AOCS Methods are done with only one measurement. Traditional visual color values like the iodine color value, Hazen or Gardner are displayed as well as modern color systems, e.g. CIE-L*a*b* or color measurements corresponding to European or US pharmacopeia.Also transmission, extinction measurements and wavelength scans are possible so that the instrument has a multi purpose in the laboratory or production. The intuitive operation by a high-resolution touchscreen makes measuring easy in routine analysis. The measuring results can easily be transferred to an existing laboratory network via Ethernet interface.All important color scales included in one instrumentSimple integration into the laboratory network through Ethernet connectionHigh level of measurement reliability through a comprehensive set of test aidsEasy handlingAll important color scales included in one instrumentThe Lico 620 with up to 5 color scales is designed for fast routine measurements in the laboratory and in production facilities. It is already in use in a wide variety of areas in the chemical industries for quality and production control, e.g. to assess surfactants, oils, fats, resins and synthetic resins.The Lico 690 Spectral Colorimeter is flexible to use and works with many applications, such as chemical, pharmaceuticals, oil industries and the food and beverage industry. 26 color scales are directly integrated in the instrument: conventional scales like iodine, Hazen (Pt Co), Gardner, Pharmacopoeia as well as specific scales like Saybolt or ASTM.Simple integration into the laboratory network through Ethernet connectionLico instruments can be easily integrated to existing laboratory networks through an Ethernet interface.High level of measurement reliability through a comprehensive set of test aidsCertified test filters, reproducible standard color solutions and an integrated implementation of AQA (Analytical Quality Assurance) ensure optimum measurement reliability. Measured values can be evaluated in all scales, even post-measurement with archived spectral data.Easy handlingThe measurement process starts automatically when the sample cell is inserted, and the measurement vial is identified by the instrument. The easy-to-change cell compartment facilitates cleaning and/or replacement.The operation of the Lico colorimeters requires only minimum training effort thanks to clear instructions on the color touch-screen. What's in the box?Instrument, power supply, printed basic user manual, CD with full user manual, 10 mm cell adapter, dust cover SpecificationsColor Scales:European, US and Chinese Pharmacopoeia (EP, USP, CP); DIN 6162 Iodine; ISO 6271 Hazen (Pt/Co, APHA, ASTM D1209, D5386); ISO 4630 Gardner (ASTM D1544, D6045, D6166); ISO 27608 Animal and Vegetable Fats and Oils; ISO 11664 Colorimetry; ASTM E308 CIE Color; ASTM D156 Saybolt; ASTM D1500 Mineral Oil (ISO 2049); ASTM D848 Acid Wash Test; ASTM D1925 Yellowness Index (ASTM D5386); AOCS Cc13e, BS 684 Ly/Lr; ADMI, ICUMSA, EBC, ASBC, Hess-IvesCuvette Compatibility 2:10 mm rectangular sample cellCuvette Compatibility 3:50 mm rectangular sample cellDisplay:TFT WVGA color graphic touch-screenDisplay Resolution:480 - 800 pixelDisplay Size:17.8 cm (7 in.)Display Type:Color graphicIncludes:Cell adapter, dust cover, power supply, user manualInterface:2x USB Typ A, 1x USB Typ B, 1x EthernetMemory:100 color references; 1000 photometric values; 20 wavelength scans; 20 time scans; 3000 color readingsModel:Lico 690Operating Temperature Range:10 - 40 °COptical System:0° / 180° rectilinearPhotometric Accuracy:0.005 Abs at 0 - 0.5 AbsPhotometric Accuracy 2:1 % at 0.5 - 2.0 AbsPhotometric Linearity:< 0.5 % to 2 Abs with neutral glass at 546 nmPhotometric Linearity 2:≤ 1 % with neutral glass at 546 nmPhotometric Measuring Range:±3.0 Abs (wavelength range 340 - 900 nm)Power Requirements:110 V - 240 VReproducibility:±0.2 % transmissionSample Cell Compatibility:11 mm round sample cellStandard Illuminant:A/C/D65Standard Observer:10° 2°Storage Conditions:-40 °C - 60 °CUser Interface:Touch-screen, ext. USB keyboardWavelength Accuracy:±1.5 nm (wavelength range 340 - 900 nm)Wavelength Calibration:AutomaticWavelength Range:380 nm - 720 nm used for colorimetric calculationsWeight:4.2 kgPart NumberColor ScalesStandard IlluminantMemorySipper (optional)Spectral scanUSD PriceLMV187.53.40001 CompareEuropean, US and Chinese Pharmacopoeia (EP, USP, CP); DIN 6162 Iodine; ISO 6271 Hazen (Pt/Co, APHA, ASTM D1209, D5386); ISO 4630 Gardner (ASTM D1544, D6045, D6166); ISO 27608 Animal and Vegetable Fats and Oils; ISO 11664 Colorimetry; ASTM E308 CIE Color; ASTM D156 Saybolt; ASTM D1500 Mineral Oil (ISO 2049); ASTM D848 Acid Wash Test; ASTM D1925 Yellowness Index (ASTM D5386); AOCS Cc13e, BS 684 Ly/Lr; ADMI, ICUMSA, EBC, ASBC, Hess-IvesA/C/D65100 color references; 1000 photometric values; 20 wavelength scans; 20 time scans; 3000 color readingsYesYesContact HachLMV187.53.20001 CompareDIN 6162 iodine; ISO 6271 Hazen (Pt/Co, APHA, ASTM D1209, D5386); ISO 4630 Gardner (ASTM D1544, D6045); ASTM D 156 Saybolt; ASTM D 1500 mineral oilC 2°400 color readingsNoNoContact Hach

Alat Laboratorium UmumSL1000 - PPA Portable Parallel Analyzer- Portable Colorimeter with USBChloramination Testing Can be Done 75% FasterDo you spend too much time on multi-parameter analysis in your distribution system or other clean water applications?Complete more tests on site, get the results you need faster, allowing you to visit more sites in each shift. Perform up to four colorimetric and two probe-based measurements in parallel 75% faster than with other methods.Do you struggle with consistency, repeatability, or inter-operator variability when performing colorimetric and probe-based analysis?Automation and internal temperature control make the entire process consistent and repeatable, while applying the same processes as current Hach methods. Avoid manual steps that can introduce variability, even when performed by experienced testers.Would you benefit from performing all your field testing on a single instrument with less hassle, fewer bulky accessories, and less clean-up? A single instrument combines colorimetric and probe-based testing in a field kit that requires fewer bulky accessories. All chemicals and processes are entirely contained inside the Chemkey. There are no powder pillows or glass vials to handle.Chloramination Testing Can be Done 75% Faster!The Hach SL1000 Portable Parallel Analyzer (PPA) performs the same tests with less than half the manual steps. Get highly accurate results, with less opportunity for errors, in a fraction of the time. Up to six parameters, tested in parallel. The SL1000 is a portable colorimeter that provides 75% faster testing in chloramination applications by using Chemkey reagents instead of powder pillows. All chemicals and processes are entirely contained inside the Chemkey.Colorimetric tests include: monochloramine, free and total ammonia, free and total chlorine, nitrite, copper, high and low range orthophosphate, high and low range hardness, high and low range alkalinity, dissolved iron, and peracetic acid.Probe-based tests include: pH, conductivity, ORP, dissolved oxygen, nitrate, and fluoride (temperature is included with each probe).To learn more about Portable Parallel Analysis (PPA) please visit: https://www.hach.com/sl1000-ppaPerform multiple tests fasterLess VariabilityLess HasslePerform multiple tests fasterComplete more tests on site, get the results you need faster, allowing you to visit more sites in each shift. Perform up to four colorimetric and two probe based measurements in parallel 75% faster than with other methods.Less VariabilityAutomation and internal temperature control make the entire process consistent and repeatable, while applying the same processes as current Hach methods. Avoid manual steps that can introduce variability, even when performed by experienced testers.Less HassleA single instrument combines colorimetric and probe testing in a field kit that requires fewer bulky accessories. All chemicals and processes are entirely contained inside the Chemkey. There are no powder pillows or glass vials to handle. What's in the box?SL1000 meter, carrying case, 1 instrument sample cup, 2 probe sample cups, rechargeable battery, battery charger, hand strap, instrument manual, and USB cable. SpecificationsBattery Life:>200 Chemkey tests per full battery chargeBattery Requirements:Rechargeable Lithium-Ion battery packCertifications:CE CompliantDetector:Silicon photodiodeEnclosure Rating:IP64Includes:SL1000 meter, carrying case, 1 instrument sample cup, 2 probe sample cups, rechargeable battery, battery charger, hand strap, instrument manual, and USB cable.Instrument Bundle:SL1000 - PPA Portable Parallel Analyzer- Portable Colorimeter with USBInterfaces:Mini USBLamp Type:Light Emitting Diode (LED)Measurement Modes:Transmittance (%), Absorbance (abs) and Concentration (Conc)Operating Temperature Range:5 - 50 °C / maximum 85% relative humidity (non-condensing)Protection Class:IIIStorage Conditions:-20 - 60 °C / maximum 85% relative humidity (non-condensing)Warranty:1 yearWeight:2.65 lbs. (1.2 kg)

Reagent ChemicalsFor determination of Cyanide by the Pyridine-Pyrazalone Method. Hach Method 8027. Range: 0.002 - 0.240 mg/L CN-. Sample Size: 10 mL. Reagent Set Includes: CyaniVer짰 3, 4, and 5 Cyanide Reagent Powder Pillows for 100 tests. SpecificationsInstrument: All except DR/3000,DR/2000, DR 900,PC IIMethod: 8027Method Name: Pyridine-PyrazaloneNumber of tests: 100Parameter: CyanidePlatform : Powder PillowsRange: 0.002 - 0.240 CN

Alat Laboratorium UmumHQ430D Water Quality Laboratory Biochemical Oxygen Demand (BOD) Meter Package with Optical LBOD101 SensorDurable benchtop meters for laboratory use.Designed for water quality experts, the Hach HQ430D Laboratory Multi-Meter is an advanced laboratory meter that takes the guesswork out of measurements. HQD meters connect with smart Intellical electrodes that automatically recognize the testing parameter, calibration history, and method settings to minimize errors and setup time. The advanced HQD Laboratory Meter is designed to withstand years of continuous lab use. HQD meters feature a simple user interface that does not require manuals or training to operate. The Intellical LBOD101 is the latest embodiment of Hach’s patented Luminescent Dissolved Oxygen (LDO) technology. The LBOD101 is a digital, luminescent dissolved oxygen (LDO) sensor with a replaceable, integrated stirring system. The LBOD101 measures the dissolved oxygen for BOD (Biochemical Oxygen Demand) determination in BOD bottles in BOD5 testing applications. The LBOD101 electrode is used for initial and final dissolved oxygen measurements.Make your Biochemical Oxygen Demand (BOD) water laboratory quality parameters testing more efficient and flexibleIntuitive user interface for simple operation, reliable and accurate resultsTrust your measurements - Intellical™ smart probes store all calibrations in the probeEnhance data connectivity with easy to read resultsComplete convenient kitMake your Biochemical Oxygen Demand (BOD) water laboratory quality parameters testing more efficient and flexibleSingle input channel for flexible measurement of pH, Conductivity, Total Dissolved Solid (TDS), Optical Dissolved Oxygen (DO), Biochemical Oxygen Demand (BOD), Oxydo Reduction Potential (ORP/RedOx), Temperature, Ion Selective Electrode (ISE) direct concentration reading for Ammonia, Ammonium, Fluoride, Chloride, Sodium - connect any Intellical™ smart probe.Intuitive user interface for simple operation, reliable and accurate resultsGuided calibration and check standard routines reduce calibration errors while stabilization alerts and visual measurement lock ensure that you can trust the accuracy of the results.Trust your measurements - Intellical™ smart probes store all calibrations in the probeCalibration history allows quick and easy change out of probes without re-calibrating. The HQD™ smart system records serial numbers, current calibration data, user ID, sample ID, time, and date automatically in the data log for complete Good Laboratory Practice (GLP) traceability.Enhance data connectivity with easy to read resultsInternal USB ports simplify data transfer, peripherals, and software updates and connection to PCs printer and keyboards, with a large ultra-bright backlit LCD screen with large font size for convenient reading.Complete convenient kitPackage content includes everything you need to start testing. Details below What's in the box?Meter package includes HQ430D Laboratory Multi Meter, LBOD101 Luminescent/Optical Dissolved Oxygen (LDO) electrode for BOD Measurement with 1 m cable, Disposable 300 mL BOD Bottle (100 pcs), BOD Bottle Stoppers (25 pcs), BOD Bottle cap (6 pcs), 4 Alkaline 1,5V AA batteries, Power Supply Adapter, Power Cord, USB cable for data transfer, and Operating Documentation. SpecificationsAutomatic Buffer Recognition:YesBarometric Pressure Measurement:Automatic compensation of DO when using an LDO or LBOD probeBOD5/CBOD resolution:Available when used with Hach WIMS BOD Manager softwareBOD Bottle:300 mL/100 pcsCalibration:Demal (1D/ 0.1D/ 0.01D);Molar (0.1M/ 0.01M/0.001M);NaCl (0.05%; 25µS/cm; 1000µS/cm; 18mS/cm);Standard sea water;User definedCalibration Intervals/Alerts/Reminder:Off, Selectable from 2 hours to 7 daysCommunication:Integrated USB type A (for USB 2.0 flash memory device, printer, keyboard) and Integrated USB type B (for PC)Compliance Certifications:CE.WEEEConductivity measurement:YesConductivity measurement: Temperature correction:None; Linear; NaCl Non-Linear Natural Water.Conductivity Measurement Range:0.01 µS/cm - 200.0 mS/cmConductivity resolution:0.01 µS/cm - 0.1 mS/cm upon selected measuring rangeContents:Meter + Probe(s) + Lab. AccessoriesCustom Calibration Standards:YesData Export:Download via USB connection to PC or flash memory device. Automatically transfer entire data log or as readings are taken.Data Memory:500 records/FIFOData Storage:Automatic, GLP ISO compliant reading data stored with calibration details.Dimensions:859 x 175 x 235 mm (3.38 x 6.88 x 9.25 in.)Display:Detailed mode/Large modeDisplay Lock Function:Continuous / Auto-stabilization ("press to read") / At IntervalDisplay Type:440 x 160 pixel LCD with backlight illuminationDO Measurement Range:0.1 - 20.0 mg/L (ppm) 1 - 200% saturationDO Resolution:0.1DO sensor calibration:• 100% (water-saturated air (100%) calibration• 100% with 0 (water-saturated air (100%) calibration with 0 point• mg/L (calibration with a specified dissolved oxygen concentration (mg/L) solution)• mg/L with 0 (calibration with a specified dissolved oxygen concentration (mg/L) solution with 0 point)• Factory (calibration with the default LDO calibration)Electrode Holder:NAElectrode stand:OptionalGLP Features:Date; Time; Sample ID; Operator IDInstrument:BenchIP Rating:IP54 (Resistant to spray of water; Dust-proof)ISE Direct Measurement Range:YesISE Electrode Calibration:2 - 5 pointsLanguages:English, French, German, Italian, Spanish, Danish, Dutch, Polish, Portuguese, Turkish, Swedish, Czech, RussianMeasurement Method:Luminescent Dissolved OxygenModel:HQ430D – Multi/1 ChannelmV Measurement at Stable Reading:YesmV Measurement Range:-1500 - 1500 mVmV Resolution:0.1 mVNeeded Cable Length:1Operating Error Messages:Clear text error messages displayedOperating Humidity:90 % relative humidity (non-condensing)Operating Interface:Soft Touch KeypadOperating Temperature:0 - +60 °C (32 - 140 °F)ORP Electrode Calibration:Predefined ORP standards (including Zobell's solution)Parameter:pH/Oxydo Reduction Potential (ORP)Conductivity/Total Dissolved Solid (TDS)/Salinity/ResistivityDissolved Oxygen (DO)Biochemical Oxygen Demand (BOD)Ion Selective Electrode (ISE): Ammonia, Ammonium, Chloride, Fluoride, Nitrate, SodiumPC Data Transfer Software:HQd Series Meter Data Transfer UtilitypH Buffer Sets:Color-coded: 4.01, 7.00, 10.01 pH;IUPAC: 1.679, 4.005, 7.000, 10.012, 12.45 pHDIN: 1.09, 4.65, 9.23 pHUser-defined custom buffer setspH Electrode calibration:1 - 3 Calibration pointsCalibration summary data logged and displayedpH Measurement Range:0 - 14 pHpH Resolution:Selectable:0.001/0.01/0.1 pHPrinter:Yes, OptionalProbes included:LBOD10101Range:0.05 - 20.00 mg/LRegion:USResistivity Measurement:2.5 Ω.cm - 49 MΩ.cmResistivity Resolution:0.1Salinity Measurement Range:0 - 42 (ppt) (‰)Salinity Resolution:0.01 (ppt) (‰)Sensors:Sensor A: LBOD10101Sensor B: NASensor C: NATDS Measurement Range:0.00 mg/L - 50.0 g/L as NaClTDS Resolution:0.01 mg/L - 0.1 g/L upon measuring range.Temperature Compensation:Automatic Temperature compensation for pHTemperature Measurement:°C or °FTemperature Range:-10°C - 110 °CTemperature Resolution:0.1Type of Measurement:Lab Wasterwater MonitoringWarranty:3 yearsWeight:750 g (1.65 lb) without batterie; 850 g (1.87 lb) with batteriesParameter/Range/Reagent InformationBOD (Biochemical Oxygen Demand)MethodRangeReagent Set(s)USEPA Compliant? 103600.05 - 20.00 mg/L BODView 

Alat Laboratorium UmumOrbisphere 6110 Total O2/CO2 Package analyzer & Installation KitTotal Package analyzer for Oxygen & Carbon Dioxide MeasurementsThe Orbisphere 6110 boasts the latest technology in final package analysis for measurements of Total Package Oxygen, Headspace Oxygen and Dissolved Oxygen; as well as dissolved Carbon Dioxide and Headspace Volume. It has been designed to meet the practical needs of both lab and at-line environments. The high-quality touch-screen facilitates measurement customisation on all types and sizes of cans or bottles, as well as providing critical information on the health of the instrument. Utilisation of this instrument has been proven to provide critical quality information of the final package, increasing process control and beverage quality.0Fast, Effective OperationReliable and FlexibleGas Phase MeasurementMaximize the Uptime of your 6110 Total Package analyzerFast, Effective OperationThe 6110 delivers repeatable analysis with minimal operator intervention. The package positioning aid with laser crosshairs confirms optimal placement and the intuitive touch-screen interface ensures product sampling is completed quickly, easily, and consistently for both line operators and lab personnel. There is no sample preparation necessary for total package and head space oxygen analysis.Reliable and FlexibleThe 6110 Total Package analyzer operates on all types of cans and bottles due to its unique gas extraction and piercing system, resulting in reliable analysis with no container leakages. The CO2 analysis measurement provides accurate results at any temperature, without having to warm the sample. The 6110 can also compensate CO2 results for any package Nitrogen content – a perfect choice for analysis directly at the filler.Gas Phase MeasurementThe Hach Orbisphere 6110 analyzes beverages without removing any product from its container. The measurement takes place in the gas phase, so there is no direct liquid contact with the 6110’s sensing technology or sampling path. This reduces maintenance by eliminating hassles such as bleaching tubing and replacing valves to prevent fouling.Maximize the Uptime of your 6110 Total Package analyzerOur expert service team works in partnership with you to provide professional start-up and commissioning and regular maintenance for your 6110 Total Package analyzer to ensure it is in the optimal condition. Please speak with your local Hach representative for service offerings in your region. What's in the box?Orbisphere 6110 Total Package Analyzer (sensors pre-installed) with Installation Kit, User Manual. See user manual on downloads tab for installation kit components. SpecificationsCommunication Capabilities:1x Ethernet, 1x USB-ACompliance Certifications:European directives: Low voltage 2006/95/EC; EMC 2004/108/ECElectromagnetic compatibility standards: EN61326Safety standard: IEC/UL/CSA 61010-1Safety of Laser products: IEC/UL/CSA 60825-1Dimensions (H x W x D):942 mm x 540 mm x 537 mmDisplay Type:Digital TFT VGA (640 x 480) colour touch screenEnclosure Rating:IP20Installation Requirement:Power requirements: 100/240 VAC, 50/60 HzPurge gas: CO2 with purity >99.9% at 6 to 7 bar abs (87 to 102 psi)Operating Conditions:Package temperature: -2 - 30 °C (28 - 86 °F) Package pressure: 1.4 - 6.8 bar (20 - 73 psi) Ambient temperature: 0 - 40 °C (32 - 104 °F)Operating System:Windows® CE 4.2Package Type:Closure types: metallic, PETPackage height:min. 90 mm (3.54 in.)max. 340 mm (13.39 in.)Package volume: min. 150 mLPower Consumption:250 VA maximumPower Requirements (Hz):50/60 HzPower Requirements (Voltage):100/240 VACRange:O2: 1 ppb - 12 ppmCO2: 0.75 - 5 v/v or 1.5 - 10 g/kgRepeatability:TPO: ±5 µg/L / ±10%,whichever is greaterCO2: ±0.05 v/v or 0.10 g/kg ±2 %, whichever is greater, measured on equilibrated packages at 10 - 25 °CTypical Analysis Time:Approximately 4 minutesUnits:O2 Concentration: ppb, ppmCO2 Concentration: v/v, g/kg, g/L %WTotal Package Quantities: mg, mL, mg/L,mL/L, µg/LPressure: bar, mbar, psiTemperature: °F, °C, KWeight:55 kgParameter/Range/Reagent InformationCarbon DioxideMethodRangeReagent Set(s)USEPA Compliant? Thermal Conductivity (TC)0 - 10 g/kg CO2  

Alat Laboratorium UmumInfracal 2 ATR-SP TOG/TPH AnalyzerSimple, portable TOG/TPH testing for process control.The InfraCal Model ATR-SP is recommended for measuring oil in water, TPH in soil or FOG in wastewater concentration levels when using hexane as the extracting solvent. Measurement data obtained with this analyzer will correlate to EPA Method 1664 as both procedures are based on evaporation techniques and measuring the residual oil and grease. The analyzer is equipped with a built-in cubic zirconia horizontal attenuated total reflection (HATR) stainless steel sample stage.Time Savings.Less Solvent.Convenient Package.Time Savings.The Infracal 2 runs tests in ~10 minutes; a fraction of the time compared to other methods, saving time, reducing costs, and increasing productivity.Less Solvent.The Infracal 2 uses up to 90% less solvent per test, reducing costs and increasing safety.Convenient Package.The Infracal 2's small size and light weight take up less space in the lab. The internal battery pack enables operators to take the instrument afield for on-site measurements. SpecificationsDimensions (H x W x D):17 x 19.8 x 13.2 cm (6.7 x 7.8 x 5.2” )Electrical Specifications:Power supplyInput: 100 - 250 VAC, 50/60 HzOutput: 18 VDC, 3.3 A max.Output Power: 60 W max.Internal 18 V battery packMeasurement Method:InfraredWeight:2.6 kg (5.8 lbs)

Alat Laboratorium UmumDR300 Pocket Colorimeter, Chlorine, Free + Total, with BoxProven past. Innovative future.The DR300 maintains the Pocket Colorimeter legacy of reliability while providing state-of-the-art data transfer capability and connection to Claros*. Reduce data collection hassles, eliminate transcription errors, and ensure stronger compliance traceability.Please note that reagents are not included in the kit and need to be purchased separately.For a limited time the DR300 comes with a FREE 90-day trial of Claros Collect software, allowing measurement data to immediately be available online to your entire team. Learn more at hach.com/claros/InstrumentConnect.*Claros connectivity currently available only in US, Canada and EU.Connected*ReliableSimpleConnected*Optional Bluetooth connectivity allows you to safely transfer measurement data to Claros – Hach®’s Water Intelligence System – reducing errors and saving time by eliminating manual data entry.ReliableRugged, waterproof (IP67) design withstands whatever conditions you encounter in the field (drops, extreme temperatures, rain and dirt) and still delivers years of dependable, accurate measurements.SimpleSimple, intuitive operation reduces potential manual error, ensuring accurate measurement data you can trust, time after time. Larger display with improved backlight makes reading measurements in all conditions even easier. 

Buret / BuretteAT1000 Potentiometric Titrator with 1 Burette – Model AT1102Simply add your sample, press the button and read your titration resultsThe AT1102 model is an accurate, reliable and easy to use instrument for performing titrations in the laboratory. This titrator was designed in Germany as part of the Hach Titralab® AT1000 family of automatic titrators and includes one burette and two measurement inputs. The titrator is delivered preassembled for easy installation and does not require complex programming like other titration systems on the market. This system offers superb dependability so you don’t suffer from downtime and it is easy to use for all skill levels, reducing operator training and process time. In fact, with an autotitrator the operator will be able to begin preparing the next sample while the instrument is performing the current measurement, thus improving lab throughput. More importantly however, the automatic titrator eliminates manual processes and operator interpretation, significantly improving accuracy and reliability so you can trust your measurements from day to day. If you perform any of the titrations listed in the Application Packs section below this is the instrument for you!Application PacksThe AT1102 instrument can be used with the following Hach Application Packs:- pH & Alkalinity in Water (Hach p/n AP0001.AT1102)- pH/Alkalinity & Conductivity (Hach p/n AP0002.AT1102)- FOS/TAC - Volatile Acids & Alkalinity in Biogas (Hach p/n AP0006.AT1102)- pH & Total Acidity in Wine & Juices (Hach p/n AP0008.AT1102)- TAN (Hach p/n AP0015.AT1102)- TBN (Hach p/n AP0016.AT1102)- BR₂/I₂ Number (Hach p/n AP0018.AT1102)Each application pack includes a pre-programmed application that runs on the instrument as well as a set of accessories necessary to perform your titrations. Please review the specific webpage for each application pack for further details, and we suggest selecting your Application Pack before your instrument. If you haven’t found the application pack that meets your needs on this page please enter “AT1000 Application Pack” in the search field, hit enter and then click on the “PRODUCT FAMILY: AT1000 Application Packs” to see the full list of Hach’s AT1000 Application Packs.Ordering InformationA base titration system consists of an Application Pack and an Instrument, so please make sure you add the Application Pack you’ve chosen and the Instrument (in this case Hach p/n AT1102) to your Hach order. In addition, make sure you added the reagents required to perform your titration measurements when selecting your Application Pack. If you did not do this yet, navigate to the Application Pack website, review the method found under the “Parameter/Reagent” tab for a list of reagents and then select what you need from the “Consumables” tab. If you have any questions about the instrument, the application packs or the reagents after reviewing our website content please contact Hach Technical support. We have a great team of experts who can quickly and painlessly guide you through the process.Get your AT1000 Titration System on the way by clicking "Add to Cart" today!AT1102 Key BenefitsAccurate and Reliable Titration ResultsEasy to Use for all OperatorsLow Cost of OwnershipImproves Lab SafetyLow MaintenanceAccurate and Reliable Titration ResultsEliminates errors in manual processes and operator interpretationPre-programmed titration methods automatically detect endpoints and perform calculationsHigh resolution electronic burette with 20,000 stepsHigh performance probes for reliable measurementsEasy to Use for all OperatorsPress one button to get the correct resultOperators of all skill levels can get accurate measurementsNo need for custom programming with Hach’s unique application specific routinesSimple user interface with large color display that shows the titration curve as it is measuringUSB ports to quickly and easily capture data to a PC and attach optional keyboard/mouse or printerLow Cost of OwnershipReduces the amount of reagent used for every titration cutting cost of ownership month after monthIncreases lab throughput by allowing operator to prepare next sample while titrator performs measurementAdding an AS1000 sample changer allows the operator to load multiple samples and come back for results laterImproves Lab SafetyMinimizes direct contact with reagentsNo need for potentially dangerous colored indicatorsInstrument can be easy and safely moved thanks to the compact designLow MaintenanceReliable design significantly reduces downtimeExtended periods between maintenance routinesMaintenance is simple and easy to perform What's in the box?Hach AT1102 Instrument, Tube Holder, Sensor Storage Tubes, Power Supply, Power Cord, ManualSold Separately: Don't forget to order your Application Pack and Reagents and consider purchasing an AS1000 Sample Changer! SpecificationsAccessories:Supported peripherals: printer, PC software, balance, sample changer, keyboard, mouse, barcode reader, sampling pump, propeller stirrerApplication:5Automatic Reagent Addition(s):Integrated peristaltic pumps for reagent additionBeaker Volumes Accepted:System specific beakers: Polypropylene, 50 mL & 150 mL with clipsGeneric beakers supported: Up to 250 mL low form glassBurette:1Burette: Volumes Available:2.5/5/10/25 mL, ISO8655-3Burette Motor Resolution:20,000 steps with electronic µstepping technology (128 µsteps/step)Calibration:Titrant & electrode (up to 5 buffers in Auto Mode, fixed & user defined)Calibration Curves Display:Direct & derivative titration curves, electrode calibration curveCalibration Intervals/Alerts/Reminder:Yes, user defined periodCertifications:Safety IEC/EN 61010-1; EMC IEC/EN 61326-1Data Export:On USB flash drive, CSV format, Excel compatibleData Memory:Last 100 samples, QC & blank analyses, last 10 calibrationsData Storage:Date, Time, Operator IDs, Sample IDsDisplay Type:5,7"; Graphic color; VGAElectrode:IntelliCAL ("Plug & Play" digital), analog, photocolorimetric; 2 Inputs availableEmbedded Procedures:Tubing bubble purging, reagent priming, burette and pump replacementInstallation Category:Category IILanguages:English, German, French, Italian, SpanishMaintenance Scheduler:Yes, user definedMaterial Enclosures:PP Latene, silicone, hardened glass, POM, stainless steel. Splashproof design.Measurement Method:Potentiometric (zero & imposed current), amperometric, colorimetricMeasurement Modes:End Point, Inflection Point - sample, blank, sample with blank, QC sample, QC sample with blankMeasurements:mV/pH, Conductivity, Temperature (°C or °F)Model:AT1102Operating Conditions:15 - 35 °C (59 - 95 °F), 20 - 80 % RH, non-condensingOperating Humidity:20 - 80 % (non-condensing)Operating Interface:Soft keypad (Silicone)Operating Temperature Range:15 - 35 °C (59 - 95 °F)Output:Electrode ports (x2), USB (x2), Serial (x1), Ethernet (x1)Parameter:mV/pH, Conductivity, TemperaturePassword Protection:Yes, user definedPollution Degree:2Power Requirements (Hz):50/60 HzPower Requirements (Voltage):100/240 VACPump flow rate:100 mL/minPumps:0Region:USRequired Application Package/s:AP0001.AT1102 pH & Alkalinity in WaterAP0006.AT1102 Volatile Acids & Alkalinity (Biogas)AP0008.AT1102 pH, Total Acidity (Milk, Tomato Sauce, & Fruit Juice)AP0015.AT1102 TANAP0016.AT1102 TBNResolution:Conductivity: ±0.5 % of reading mV/pH: ±0.1 mV / ±0.001 pH Temperature: ±0.3 °CSample Stand:Integrated, magnetic stirring, beakers up to 250 mLStorage Conditions:-5 - 40 °CSupported Peripherals:Printer, PC software, balance, sample changer, keyboard, mouse, barcode reader, sampling pump, propeller stirrerTitration Modes:Sample, blank, sample with blank, QC sample, QC sample with blankTitration Types:Potentiometric (zero & imposed current), amperometric, colorimetricWarranty:1 yearWeight:4 kgParameter/Range/Reagent InformationAcid-BaseMethodRangeReagent Set(s)USEPA Compliant? AT1000 Total Acid Number (TAN) Titration Automatic Titrator Method0.05 - 260 mg/L TANView  AT1000 Total Base Number (TBN) Titration Automatic Titrator Method1 - 100 mg/L TBNView AcidityMethodRangeReagent Set(s)USEPA Compliant? AT1000 Acidity in Milk Titration Automatic Titrator Method7 - 85 C₃H₆O₃ dg/LView  AT1000 Acidity in Tomato Sauce Titration Automatic Titrator Method2 - 24.3 g/L Citric Acid   AT1000 Acidity in Wine, Juice Titration Automatic Titrator Method2 - 24.3 g/L Citric Acid  AlkalinityMethodRangeReagent Set(s)USEPA Compliant? AT1000 Alkalinity Automatic Titrator Method40 - 2000 mg/L CaCO₃View BromineMethodRangeReagent Set(s)USEPA Compliant? AT1000 Bromine Number ASTM D1159-07 Bromine Number0.500 - 200/100 g g Br₂  FOS/TACMethodRangeReagent Set(s)USEPA Compliant? AT1000 FOS/TAC Automatic Titrator Method400 - 25000 mg/L CaCO₃View  AT1000 FOS/TAC Automatic Titrator Method600 - 80000 mg/L CH₃COOHView Part NumberBurettePumpsMeasurement MethodRequired Application Package/sUSD PriceAT1102.97 Compare10Potentiometric (zero & imposed current), amperometric, colorimetricAP0001.AT1102 pH & Alkalinity in WaterAP0006.AT1102 Volatile Acids & Alkalinity (Biogas)AP0008.AT1102 pH, Total Acidity (Milk, Tomato Sauce, & Fruit Juice)AP0015.AT1102 TANAP0016.AT1102 TBNContact HachAT1112.97 Compare11Potentiometric (zero & imposed current), amperometric, colorimetricAP0003.AT1112 Ca & Mg Hardness in waterAP0010.AT1112 Salt in food productsContact HachAT1122.97 Compare12Potentiometric (zero & imposed current), amperometric, colorimetricAP0007.AT1122 Free & Total Chlorine, Chlorine Dioxide, Chlorite, & Sulfite (Autocat)AP0012.AT1122 Free & Total SO₂ in wineContact HachAT1222.97 Compare22Potentiometric (zero & imposed current), amperometric, colorimetricAP0005.AT1222 pH, Alkalinity & Hardness in WaterAP0011.AT1222 pH, Total Acidity & Chlorides in Food & BeverageAP0013.AT1222 pH, Total Acidity, Free & Total SO₂ in WineContact HachKF1121.97 Compare12Volumetric Karl Fischer, AC or DC imposed currentAP0014.KF1121 Moisture ContentContact Hach8606600 CompareContact Hach8606700 CompareContact Hach8606900 CompareContact Hach8607000 CompareContact Hachitems per page10  |  20  |  50 page 1 of 1 Other Product Families