OVEN MEMMERT

Waterbath WNE 7Standard delivery WaterbathOn this page, you can find all the essential technical data on the Memmert water bath. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.Alat Laboratorium UmumTemperatureSetting temperature range+10 to +95 °C and boiling stageWorking temperature range in °Cmin. 5 above ambient up to +95 °C with additional boiling moderesolution of display and setting accuracy0,1°C up to +99,9°C / 1°C from 100°CControl of standard componentsControllerdigital display (LED) of all set parameters, such as temperature and alarm values (0,1°C resolution) as well as time valuesTimerdigital timer from 1 min. up to 999 hours for: ON (continuous operation), DELAYED ON, HOLD or HOLD set-temperature dependent with guaranteed holding timeCalibrationon controllerSafetyTemperature sensor2 Pt100 sensors Class A in 4-wire-circuit, mutually monitoring and taking over the performance at the same temperature valueTemperature controlmechanical temperature limiter TB protection class 1 switching the heating off at approx. 30°C above max. temperature of the bathTemperature controlindependently working, electronic overtemperature controller TWW protection class 3.1 or overtemperature limiter TWB protection class 2, adjustable in set-up menu by customerTemperature controlin case of overtemperature due to failure, the heating is switched off at approx. 10°C above the set temperature (fixed value)Autodiagnostic systemfuzzy-supported PID microprocessor controller with integrated autodiagnostic system with fault indicationAlarmvisual and acoustic alarm at programme end and as input acknowledgement as well as in case of low liquid level, heating is switched off automaticallyHeating conceptHeating Bathscorrosion-proof large-area heating on three sidesStainless steel interiorDimensions W x H x D in mmw(A) x h(C) x d(B): 240 x 140 x 210 mmInterioreasy-to-clean interior, made of stainless steel, reinforced by deep drawn ribbing, material no. 1.4301 (ASTM 304), laser-weldedVolume7 lLiquid level min.(H) 97 mmLiquid level max.(I) 120 mmTextured stainless steel casingDimensionsw(D) x h(G) x d(E): 468 x 337 x 356 mmElectrical dataVoltage230 V, 50/60 HzElectrical loadapprox. 1200 W (during heating)Ambient conditionsInstallationThe vent openings in the left and back side must remain unobstructed. Minimum wall spacing on all sides is 80 mm. The minimum spacing from the top of the bath to the next ceiling is 750 mm.Ambient temperature+5 °C to +40 °CHumidity rhmax. 80 %, non-condensingOvervoltage categoryIIPollution degree2Packing/shipping dataTransport informationThe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. cartonw x h x d: 570 x 450 x 420 mmNet weightapprox. 11 kgGross weight cartonapprox. 16 kg

Waterbath WNB 10Standard delivery WaterbathOn this page, you can find all the essential technical data on the Memmert water bath. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.Alat Laboratorium UmumTemperatureSetting temperature range+10 to +95 °C and boiling stageWorking temperature range in °Cmin. 5 above ambient up to +95 °C with additional boiling modeControl of standard componentsTemperature sensor1 Pt100 sensor class A in 4-wire-circuitTimerintegrated digital timer from 1 min. to 99,59 hours for: ON continuous operation WAIT (delayed on for continuous and limited timed operation) HOLDSafetyTemperature controlmechanical temperature limiter TB protection class 1 switching the heating off at approx. 30°C above max. temperature of the bathTemperature controlin case of overtemperature due to failure, the heating is switched off at approx. 10°C above the set temperature (fixed value)Autodiagnostic systemmicroprocessor PID-temperature controller with integrated autodiagnostic system with fault indicatorHeating conceptHeating Bathscorrosion-proof large-area heating on three sidesStandard equipmentControllerdigital display (LED) of set and actual temperature (0,1°C resolution) and of (remaining) programme timeStainless steel interiorDimensions W x H x D in mmw(A) x h(C) x d(B): 350 x 140 x 210 mmInterioreasy-to-clean interior, made of stainless steel, reinforced by deep drawn ribbing, material no. 1.4301 (ASTM 304), laser-weldedVolume10 lLiquid level min.(H) 97 mmLiquid level max.(I) 120 mmTextured stainless steel casingDimensionsw(D) x h(G) x d(E): 578 x 337 x 356 mmElectrical dataVoltage230 V, 50/60 HzElectrical loadapprox. 1200 W (during heating)Ambient conditionsInstallationThe vent openings in the left and back side must remain unobstructed. Minimum wall spacing on all sides is 80 mm. The minimum spacing from the top of the bath to the next ceiling is 750 mm.Ambient temperature+5 °C to +40 °CHumidity rhmax. 80 %, non-condensingOvervoltage categoryIIPollution degree2Packing/shipping dataTransport informationThe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. cartonw x h x d: 670 x 450 x 380 mmNet weightapprox. 13 kgGross weight cartonapprox. 19 kg

Waterbath WNB 14Standard delivery WaterbathOn this page, you can find all the essential technical data on the Memmert water bath. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.Alat Laboratorium UmumTemperatureSetting temperature range+10 to +95 °C and boiling stageWorking temperature range in °Cmin. 5 above ambient up to +95 °C with additional boiling modeControl of standard componentsTemperature sensor1 Pt100 sensor class A in 4-wire-circuitTimerintegrated digital timer from 1 min. to 99,59 hours for: ON continuous operation WAIT (delayed on for continuous and limited timed operation) HOLDSafetyTemperature controlmechanical temperature limiter TB protection class 1 switching the heating off at approx. 30°C above max. temperature of the bathTemperature controlin case of overtemperature due to failure, the heating is switched off at approx. 10°C above the set temperature (fixed value)Autodiagnostic systemmicroprocessor PID-temperature controller with integrated autodiagnostic system with fault indicatorHeating conceptHeating Bathscorrosion-proof large-area heating on three sidesStandard equipmentControllerdigital display (LED) of set and actual temperature (0,1°C resolution) and of (remaining) programme timeStainless steel interiorStainless steel interiorDimensions W x H x D in mmw(A) x h(C) x d(B): 350 x 140 x 290 mmInterioreasy-to-clean interior, made of stainless steel, reinforced by deep drawn ribbing, material no. 1.4301 (ASTM 304), laser-weldedVolume14 lLiquid level min.(H) 97 mmLiquid level max.(I) 120 mmTextured stainless steel casingDimensionsw(D) x h(G) x d(E): 578 x 347 x 436 mmElectrical dataVoltage230 V, 50/60 HzElectrical loadapprox. 1800 W (during heating)Ambient conditionsInstallationThe vent openings in the left and back side must remain unobstructed. Minimum wall spacing on all sides is 80 mm. The minimum spacing from the top of the bath to the next ceiling is 750 mm.Ambient temperature+5 °C to +40 °CHumidity rhmax. 80 %, non-condensingOvervoltage categoryIIPollution degree2Packing/shipping dataTransport informationThe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. cartonw x h x d: 670 x 530 x 400 mmNet weightapprox. 15 kg

Waterbath WNB 22Standard delivery WaterbathOn this page, you can find all the essential technical data on the Memmert water bath. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.TemperatureAlat Laboratorium UmumSetting temperature range+10 to +95 °C and boiling stageWorking temperature range in °Cmin. 5 above ambient up to +95 °C with additional boiling modeControl of standard componentsTemperature sensor1 Pt100 sensor class A in 4-wire-circuitTimerintegrated digital timer from 1 min. to 99,59 hours for: ON continuous operation WAIT (delayed on for continuous and limited timed operation) HOLDSafetyTemperature controlmechanical temperature limiter TB protection class 1 switching the heating off at approx. 30°C above max. temperature of the bathTemperature controlin case of overtemperature due to failure, the heating is switched off at approx. 10°C above the set temperature (fixed value)Autodiagnostic systemmicroprocessor PID-temperature controller with integrated autodiagnostic system with fault indicatorHeating conceptHeating Bathscorrosion-proof large-area heating on three sidesStandard equipmentControllerdigital display (LED) of set and actual temperature (0,1°C resolution) and of (remaining) programme timeStainless steel interiorDimensions W x H x D in mmw(A) x h(C) x d(B): 350 x 220 x 290 mmInterioreasy-to-clean interior, made of stainless steel, reinforced by deep drawn ribbing, material no. 1.4301 (ASTM 304), laser-weldedVolume22 lLiquid level min.(H) 177 mmLiquid level max.(I) 200 mmTextured stainless steel casingDimensionsw(D) x h(G) x d(E): 578 x 405 x 436 mmElectrical dataVoltage230 V, 50/60 HzElectrical loadapprox. 2000 W (during heating)Ambient conditionsInstallationThe vent openings in the left and back side must remain unobstructed. Minimum wall spacing on all sides is 80 mm. The minimum spacing from the top of the bath to the next ceiling is 750 mm.Ambient temperature+5 °C to +40 °CHumidity rhmax. 80 %, non-condensingOvervoltage categoryIIPollution degree2Packing/shipping dataTransport informationThe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. cartonw x h x d: 670 x 530 x 460 mmNet weightapprox. 16 kgGross weight cartonapprox. 23 kg

Universal Oven UF30delivery Universal Oven The universally applicable lab oven U is Memmert’s classic appliance for temperature control in science, research and material tests in industry. The technologically perfected masterpiece made of high-quality, hygienic, easy-to-clean stainless steel leaves nothing to be desired in terms of ventilation and control technology, overtemperature protection and precisely tuned heating technology.On this page, you can find all the essential technical data on the universal Memmert lab oven. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.Alat Laboratorium UmumTemperatureWorking temperature rangeat least 5 (UN/UNplus/UNm/UNmplus) or 10 (UF/UFplus/UFm/UFmplus) above ambient temperature to +300 °CSetting temperature range+20 to +300 °CTemperature sensor1 Pt100 sensor DIN class A in 4-wire-circuitControl technologyLanguage settingGerman, English, Spanish, French, Polish, Czech, HungarianControlCOCKPITSingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour displayTimerDigital backwards counter with target time setting, adjustable from 1 minute to 99 daysFunction SetpointWAITthe process time does not start until the set temperature is reachedCalibrationthree freely selectable temperature valuesadjustable parameterstemperature (Celsius or Fahrenheit), fan speed, air flap position, programme time, time zones, summertime/wintertimeVentilationFanforced air circulation by quiet air turbine, adjustable in 10 % stepsFresh airAdmixture of pre-heated fresh air by electronically adjustable air flapVentvent connection with restrictor flapCommunicationDocumentationprogramme stored in case of power failureProgrammingAtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).SafetyTemperature controladjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperatureAutodiagnostic systemfor fault analysisStandard equipmentDoorfully insulated stainless steel door with 2-point locking (compression door lock)Internals1 stainless steel grid(s), electropolishedWorks calibration certificateCalibration at +160°C

MEMMERT Incubator IN55Alat Laboratorium UmumMulai dariCall PriceKatalogIN55BrandMemmertKondisiNewLampiranDescription:Incubator IN55, natural convection, SingleDISPLAY, 53 l, 20 °C - 80 °C with 1 gridPropertiesControl of standard componentsTemperature1 Pt100 sensor DIN class A in 4-wire-circuitControlCOCKPITadaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour displayTimerDigital backwards counter with target time setting, adjustable from 1 minute to 99 daysTemperatureSet temperature range in °Cmin. 5°C above ambient up to +80°Cresolution of display for setpoint and actual temperature values0.1°CControl technologyFunction SetpointWAITthe process time does not start until the set temperature is reachedLanguage settingGerman/English/Spanish/FrenchCalibrationthree freely selectable temperature valuesadjustable parameterstemperature (Celsius or Fahrenheit), air flap position, programme time, time zones, summertime/wintertimeVentilationnatural convectionFresh air admixtureadjustment of pre-heated fresh air admixture by air flap control in 10 % stepsVentvent connection with restrictor flapCommunicationDocumentationprogramme stored in case of power failureProgrammingAtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).SafetyTemperature controladjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperatureAutodiagnostic systemfor fault analysisStandard equipmentScope of deliveryincl. works calibration certificate for +37°CDoorfully insulated stainless steel door with 2-point locking (compression door lock)Doorinner glass doorHousingrear zinc-plated steelInterioreasy-to-clean interior,made of stainless steel,reinforced by deep drawn ribbing with integrated and protected large-area heating on four sidesInternals1 stainless steel gridStainless steel interiorMax. loading of chamber: 80 kgDimensions W x H x D in mmw(A) x h(B) x d(C): 400 x 400 x 330 mmVolume 53 lTextured stainless steel casingw(D) x h(E) x d(F): 585 x 784 x 514 mmElectrical dataVoltage Electrical load230 V, 50/60 Hzapprox. 1000 WVoltage Electrical load115 V, 50/60 Hzapprox. 900 WPacking/shipping datathe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. carton B x H x T: 730 x 950 x 670 mmNet weight approx. 57 kgGross weight carton approx. 76 kG

Steriliser SN30Alat Laboratorium UmumStandard delivery SteriliserThe indispensable safety feature for this hot air steriliser: Setpoint Wait. This means that the programme for sterilisation only starts when the set temperature has been reached. This feature can also be used with freely positionable Pt100 temperature sensors. Here the sterilisation time only begins when the set temperature has been reached at all measurement points, and reliable sterilisation is guaranteed at all times.On this page, you can find all the essential technical data on the Memmert hot air steriliser. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.TemperatureSetting temperature range+20 to +250 °CWorking temperature rangeat least 5 above ambient temperature to +250 °CTemperature sensor1 Pt100 sensor DIN class A in 4-wire-circuitControl technologyLanguage settingGerman, English, Spanish, French, Polish, Czech, HungarianControlCOCKPITSingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour displayTimerDigital backwards counter with target time setting, adjustable from 1 minute to 99 daysFunction SetpointWAITthe process time does not start until the set temperature is reachedCalibrationthree freely selectable temperature valuesadjustable parameterstemperature (Celsius or Fahrenheit), air flap position, programme time, time zones, summertime/wintertimeVentilationConvectionnatural convectionFresh airAdmixture of pre-heated fresh air by electronically adjustable air flapVentvent connection with restrictor flapCommunicationDocumentationprogramme stored in case of power failureProgrammingAtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).SafetyTemperature controladjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperatureAutodiagnostic systemfor fault analysisStandard equipmentDoorfully insulated stainless steel door with 2-point locking (compression door lock)Internals1 stainless steel grid(s), electropolishedWorks calibration certificateCalibration at +160°CTemperatureSetting temperature range+20 to +250 °CWorking temperature rangeat least 5 above ambient temperature to +250 °CTemperature sensor1 Pt100 sensor DIN class A in 4-wire-circuitControl technologyLanguage settingGerman, English, Spanish, French, Polish, Czech, HungarianControlCOCKPITSingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour displayTimerDigital backwards counter with target time setting, adjustable from 1 minute to 99 daysFunction SetpointWAITthe process time does not start until the set temperature is reachedCalibrationthree freely selectable temperature valuesadjustable parameterstemperature (Celsius or Fahrenheit), air flap position, programme time, time zones, summertime/wintertimeVentilationConvectionnatural convectionFresh airAdmixture of pre-heated fresh air by electronically adjustable air flapVentvent connection with restrictor flapCommunicationDocumentationprogramme stored in case of power failureProgrammingAtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).SafetyTemperature controladjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperatureAutodiagnostic systemfor fault analysisStandard equipmentDoorfully insulated stainless steel door with 2-point locking (compression door lock)Internals1 stainless steel grid(s), electropolishedWorks calibration certificateCalibration at +160°C

Waterbath WNB 7Alat Laboratorium UmumStandard delivery WaterbathOn this page, you can find all the essential technical data on the Memmert water bath. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.TemperatureSetting temperature range+10 to +95 °C and boiling stageWorking temperature range in °Cmin. 5 above ambient up to +95 °C with additional boiling modeControl of standard componentsTemperature sensor1 Pt100 sensor class A in 4-wire-circuitTimerintegrated digital timer from 1 min. to 99,59 hours for: ON continuous operation WAIT (delayed on for continuous and limited timed operation) HOLDSafetyTemperature controlmechanical temperature limiter TB protection class 1 switching the heating off at approx. 30°C above max. temperature of the bathTemperature controlin case of overtemperature due to failure, the heating is switched off at approx. 10°C above the set temperature (fixed value)Autodiagnostic systemmicroprocessor PID-temperature controller with integrated autodiagnostic system with fault indicatorHeating conceptHeating Bathscorrosion-proof large-area heating on three sidesStandard equipmentControllerdigital display (LED) of set and actual temperature (0,1°C resolution) and of (remaining) programme timeStainless steel interiorDimensions W x H x D in mmw(A) x h(C) x d(B): 240 x 140 x 210 mmInterioreasy-to-clean interior, made of stainless steel, reinforced by deep drawn ribbing, material no. 1.4301 (ASTM 304), laser-weldedVolume7 lLiquid level min.(H) 97 mmLiquid level max.(I) 120 mmTextured stainless steel casingDimensionsw(D) x h(G) x d(E): 468 x 337 x 356 mmElectrical dataVoltage230 V, 50/60 HzElectrical loadapprox. 1200 W (during heating)Ambient conditionsInstallationThe vent openings in the left and back side must remain unobstructed. Minimum wall spacing on all sides is 80 mm. The minimum spacing from the top of the bath to the next ceiling is 750 mm.Ambient temperature+5 °C to +40 °CHumidity rhmax. 80 %, non-condensingOvervoltage categoryIIPollution degree2Packing/shipping dataTransport informationThe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. cartonw x h x d: 570 x 450 x 420 mmNet weightapprox. 11 kgGross weight cartonapprox. 16 kg

Universal Oven UF55 Precise drying, heating, ageing, burn-in and hardening in research, science, industry and quality assurance.TemperatureAlat Laboratorium UmumWorking temperature rangeat least 5 (UN/UNplus/UNm/UNmplus) or 10 (UF/UFplus/UFm/UFmplus) above ambient temperature to +300 °CSetting temperature range+20 to +300 °CTemperature sensor1 Pt100 sensor DIN class A in 4-wire-circuitControl technologyLanguage settingGerman, English, Spanish, French, Polish, Czech, HungarianControlCOCKPITSingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour displayTimerDigital backwards counter with target time setting, adjustable from 1 minute to 99 daysFunction SetpointWAITthe process time does not start until the set temperature is reachedCalibrationthree freely selectable temperature valuesadjustable parameterstemperature (Celsius or Fahrenheit), fan speed, air flap position, programme time, time zones, summertime/wintertimeVentilationFanforced air circulation by quiet air turbine, adjustable in 10 % stepsFresh airAdmixture of pre-heated fresh air by electronically adjustable air flapVentvent connection with restrictor flapCommunicationDocumentationprogramme stored in case of power failureProgrammingAtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).SafetyTemperature controladjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperatureAutodiagnostic systemfor fault analysisStandard equipmentDoorfully insulated stainless steel door with 2-point locking (compression door lock)Internals1 stainless steel grid(s), electropolishedWorks calibration certificateCalibration at +160°CStainless steel interiorDimensionsw(A) x h(B) x d(C): 400 x 400 x 330 mm (d less 39 mm for fan)Interioreasy-to-clean interior,made of stainless steel, reinforced by deep drawn ribbing with integrated and protected large-area heating on four sidesVolume53 lMax. number of internals4Max. loading of chamber80 kgMax. loading per internal20 kgTextured stainless steel casingDimensionsw(D) x h(E) x d(F): 585 x 784 x 514 mm (d +56mm door handle)Housingrear zinc-plated steelElectrical dataVoltage Electrical load230 V, 50/60 Hzapprox. 2000 WVoltage Electrical load115 V, 50/60 Hzapprox. 1700 WAmbient conditionsSet UpThe distance between the wall and the rear of the appliance must be at least 15 cm. The clearance from the ceiling must not be less than 20 cm and the side clearance from walls or nearby appliances must not be less than 5 cm.Altitude of installationmax. 2,000 m above sea levelAmbient temperature+5 °C to +40 °CHumidity rhmax. 80 %, non-condensingOvervoltage categoryIIPollution degree2Packing/shipping dataTransport informationThe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. cartonw x h x d: 730 x 950 x 670 mmNet weightapprox. 57 kgGross weight cartonapprox. 76 kg

Universal Oven UF30Alat Laboratorium UmumStandard delivery Universal OvenThe universally applicable lab oven U is Memmert’s classic appliance for temperature control in science, research and material tests in industry. The technologically perfected masterpiece made of high-quality, hygienic, easy-to-clean stainless steel leaves nothing to be desired in terms of ventilation and control technology, overtemperature protection and precisely tuned heating technology.On this page, you can find all the essential technical data on the universal Memmert lab oven. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at myAtmoSAFE@memmert.com.TemperatureWorking temperature rangeat least 5 (UN/UNplus/UNm/UNmplus) or 10 (UF/UFplus/UFm/UFmplus) above ambient temperature to +300 °CSetting temperature range+20 to +300 °CTemperature sensor1 Pt100 sensor DIN class A in 4-wire-circuitControl technologyLanguage settingGerman, English, Spanish, French, Polish, Czech, HungarianControlCOCKPITSingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour displayTimerDigital backwards counter with target time setting, adjustable from 1 minute to 99 daysFunction SetpointWAITthe process time does not start until the set temperature is reachedCalibrationthree freely selectable temperature valuesadjustable parameterstemperature (Celsius or Fahrenheit), fan speed, air flap position, programme time, time zones, summertime/wintertimeVentilationFanforced air circulation by quiet air turbine, adjustable in 10 % stepsFresh airAdmixture of pre-heated fresh air by electronically adjustable air flapVentvent connection with restrictor flapCommunicationDocumentationprogramme stored in case of power failureProgrammingAtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).SafetyTemperature controladjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperatureAutodiagnostic systemfor fault analysisStandard equipmentDoorfully insulated stainless steel door with 2-point locking (compression door lock)Internals1 stainless steel grid(s), electropolishedWorks calibration certificateCalibration at +160°CStainless steel interiorDimensionsw(A) x h(B) x d(C): 400 x 320 x 250 mm (d less 39 mm for fan)Interioreasy-to-clean interior,made of stainless steel, reinforced by deep drawn ribbing with integrated and protected large-area heating on four sidesVolume32 lMax. number of internals3Max. loading of chamber60 kgMax. loading per internal20 kgTextured stainless steel casingDimensionsw(D) x h(E) x d(F): 585 x 704 x 434 mm (d +56mm door handle)Housingrear zinc-plated steelElectrical dataVoltage Electrical load230 V, 50/60 Hzapprox. 1600 WVoltage Electrical load115 V, 50/60 Hzapprox. 1600 WAmbient conditionsSet UpThe distance between the wall and the rear of the appliance must be at least 15 cm. The clearance from the ceiling must not be less than 20 cm and the side clearance from walls or nearby appliances must not be less than 5 cm.Altitude of installationmax. 2,000 m above sea levelAmbient temperature+5 °C to +40 °CHumidity rhmax. 80 %, non-condensingOvervoltage categoryIIPollution degree2Packing/shipping dataTransport informationThe appliances must be transported uprightCustoms tariff number8419 8998Country of originFederal Republic of GermanyWEEE-Reg.-No.DE 66812464Dimensions approx incl. cartonw x h x d: 660 x 890 x 650 mmNet weightapprox. 45 kgGross weight cartonapprox. 61 kg